The 350 HO Deluxe takes the value leading 350 HO a step further by adding carburetor, distributor, torsional damper, and 12.75in 153 tooth automatic trans flexplate.
This enhancement to the Vortec cylinder head 330 horsepower 350 HO makes it easier than ever to repower your street rod, street machine or sportsman racer.
The 600 cfm vacuum secondary Holley carburetor is ideally suited to the 350 HO. And the proven GM HEI distributor will give years of worry-free driving.
With a 9.1 to 1 compression ratio, it's pump gas friendly, and with its muscle car idle it's cruise night cool. With GMPP's lowest priced small-block crate engine there is no reason to rebuild that junk yard clunker and since it's complete from carb to pan there is no need to chase parts.
Talk to GMPartsDepot an GM Performance Parts Authorized Dealer about any additional required parts to complete your re-power project.
This engine is perfect for your 1975 or older vehicle or any off-road usage.
Service Parts Listing
Note: Engine does not come with a water pump.
350 HO Technical Information
Horsepower ..................... 330 @ 5000 RPM
Torque .......................... 380 Ft. Lbs. @ 3800
Max. Recommended RPM ..... 5500
Compression Ratio ............. 9.1:1
Block ............................ 10105123 Cast iron four bolt with one piece rear main seal
Flexplate..........................14088765 12.75in 153 teeth
Carburator....................... 19170092 Holley 670 Street advenger Crankshaft ...................... 14088527 Nodular cast iron
Connecting Rods ............... 10108688 PM steel
Pistons .......................... 12361371 Cast aluminum
Piston Rings .................... 14089025
Camshaft ........................ 24502476
Lift: .435" I, .460" E. Duration @ .050: 212o I, 222o E.
Timing Chain ................... 14087014
Cylinder Heads ................. 12558060 Cast Iron 64cc Vortec combustion chambers
Intake Valves ................... 10241743 1.94"
Exhaust Valves .................. 12550901 1.50"
Valve Springs ................... 10212811
Rocker Arms .................... 10089648 1.5 ratio
Valve Lash ...................... Zero
Spark Plugs ..................... R44TS Gap @ .045 (300 HP 350) 41-932 Gap @ .060 (330 HP 350) R44LTS Gap @ .045 (330 HP 350) Rapid Fire #8 @ .035
Ignition Timing .................. 10 BTDC @ 700 RPM
This block is drilled and tapped for clutch linkage.
Do not use # 10455709 starter for this application.
Make sure to check for hood clearance on Corvette. Intake with carb measurement from top of block to top of carb 9 1/4"
For manual transmissions use #14088648 14" or #14088646 12 3/4"
Service Parts Listing
Note: Engine does not come with a water pump.
This enhancement to the Vortec cylinder head 330 horsepower 350 HO makes it easier than ever to repower your street rod, street machine or sportsman racer.
The 600 cfm vacuum secondary Holley carburetor is ideally suited to the 350 HO. And the proven GM HEI distributor will give years of worry-free driving.
With a 9.1 to 1 compression ratio, it's pump gas friendly, and with its muscle car idle it's cruise night cool. With GMPP's lowest priced small-block crate engine there is no reason to rebuild that junk yard clunker and since it's complete from carb to pan there is no need to chase parts.
Talk to GMPartsDepot an GM Performance Parts Authorized Dealer about any additional required parts to complete your re-power project.
This engine is perfect for your 1975 or older vehicle or any off-road usage.
Service Parts Listing
Note: Engine does not come with a water pump.
350 HO Technical Information
Horsepower ..................... 330 @ 5000 RPM
Torque .......................... 380 Ft. Lbs. @ 3800
Max. Recommended RPM ..... 5500
Compression Ratio ............. 9.1:1
Block ............................ 10105123 Cast iron four bolt with one piece rear main seal
Flexplate..........................14088765 12.75in 153 teeth
Carburator....................... 19170092 Holley 670 Street advenger Crankshaft ...................... 14088527 Nodular cast iron
Connecting Rods ............... 10108688 PM steel
Pistons .......................... 12361371 Cast aluminum
Piston Rings .................... 14089025
Camshaft ........................ 24502476
Lift: .435" I, .460" E. Duration @ .050: 212o I, 222o E.
Timing Chain ................... 14087014
Cylinder Heads ................. 12558060 Cast Iron 64cc Vortec combustion chambers
Intake Valves ................... 10241743 1.94"
Exhaust Valves .................. 12550901 1.50"
Valve Springs ................... 10212811
Rocker Arms .................... 10089648 1.5 ratio
Valve Lash ...................... Zero
Spark Plugs ..................... R44TS Gap @ .045 (300 HP 350) 41-932 Gap @ .060 (330 HP 350) R44LTS Gap @ .045 (330 HP 350) Rapid Fire #8 @ .035
Ignition Timing .................. 10 BTDC @ 700 RPM
This block is drilled and tapped for clutch linkage.
Do not use # 10455709 starter for this application.
Make sure to check for hood clearance on Corvette. Intake with carb measurement from top of block to top of carb 9 1/4"
For manual transmissions use #14088648 14" or #14088646 12 3/4"
Service Parts Listing
Note: Engine does not come with a water pump.
Kunder der har købt dette produkt har også købt
